ucgui界面设计演示样例2
本文博客链接:,作者:jdh,转载请注明.
环境：
主机:WIN8
开发环境:MDK4.72
ucgui版本号：3.90
mcu: stm32f103VE
说明:
本程序基于ucgui对话框机制设计了一个界面，并用6个实体按键对界面进行控制，并添加了进度条显示
效果图：
源代码：
gui_match.h
/********************************************************************** 对码绑定界面模块头文件* (c)copyright 2014,jdh* All Right Reserved*新建时间:2014/10/24 by jdh**********************************************************************/#ifndef _GUI_MATCH_H_#define _GUI_MATCH_H_/********************************************************************** 头文件**********************************************************************/#include "world.h"/********************************************************************** 宏定义**********************************************************************//********************************************************************** 工作间隔*单位:ms**********************************************************************/#define INTERVAL_GUI_MATCH 100 /********************************************************************** 进度条显示时间*单位:ms**********************************************************************/#define TIME_PROGBAR_GUI_MATCH 3000 /********************************************************************** 函数**********************************************************************//********************************************************************** 模块加载**********************************************************************/void gui_match_load(void);/********************************************************************** 模块执行**********************************************************************/void gui_match_run(void);/********************************************************************** 设置显示状态*參数:enable:0:关闭显示,1:打开显示**********************************************************************/void gui_match_show(uint8_t enable);/********************************************************************** 得到当前的显示状态*返回:0:关闭显示,1:打开显示**********************************************************************/uint8_t gui_match_get_show(void);/********************************************************************** 得到绑定的脚镣id*返回:0:未绑定,其它:脚镣id**********************************************************************/uint16_t gui_match_get_fetter_id_bind(void);#endif
gui_match.c
/********************************************************************** 对码绑定界面模块主文件* (c)copyright 2014,jdh* All Right Reserved*新建时间:2014/10/24 by jdh*改动时间:2014/10/29 by jdh**********************************************************************//********************************************************************** 头文件**********************************************************************/#include "gui_match.h"#include "cc1100.h"#include "gui_main.h"/********************************************************************** 宏定义**********************************************************************/#define ID_FRAMEWIN (GUI_ID_USER + 0x10)#define ID_BUTTON_OK (GUI_ID_USER + 0x11)#define ID_BUTTON_CANCEL (GUI_ID_USER + 0x12)#define ID_BUTTON_UP (GUI_ID_USER + 0x13)#define ID_BUTTON_DOWN (GUI_ID_USER + 0x14)#define ID_BUTTON_LEFT (GUI_ID_USER + 0x15)#define ID_BUTTON_RIGHT (GUI_ID_USER + 0x16)#define ID_TEXT_MATCH (GUI_ID_USER + 0x17)#define ID_TEXT_ID (GUI_ID_USER + 0x18)#define ID_TEXT_PROGBAR (GUI_ID_USER + 0x19)#define ID_LISTBOX (GUI_ID_USER + 0x1A)#define ID_PROGBAR (GUI_ID_USER + 0x1B)/********************************************************************** 列表框存储的数据数量**********************************************************************/#define LIST_LEN 20/********************************************************************** 数据结构**********************************************************************//********************************************************************** 按键状态**********************************************************************/struct _Key_State{ uint8_t ok; uint8_t cancel; uint8_t up; uint8_t down; uint8_t left; uint8_t right;};/********************************************************************** 列表框缓存**********************************************************************/struct _List{ uint8_t len; uint16_t buf[LIST_LEN];};/********************************************************************** 静态变量**********************************************************************//********************************************************************** 界面句柄**********************************************************************/static WM_HWIN Handle_Gui;/********************************************************************** 资源表**********************************************************************/static const GUI_WIDGET_CREATE_INFO _aDialogCreate[] = { { FRAMEWIN_CreateIndirect, "Frame3", ID_FRAMEWIN, 0, 0, 240, 320, 0, 0x0}, { BUTTON_CreateIndirect, "OK", ID_BUTTON_OK, 5, 255, 40, 20, 0, 0x0}, { BUTTON_CreateIndirect, "Button", ID_BUTTON_DOWN, 95, 280, 40, 20, 0, 0x0}, { BUTTON_CreateIndirect, "UP", ID_BUTTON_UP, 95, 255, 40, 20, 0, 0x0}, { BUTTON_CreateIndirect, "CANCEL", ID_BUTTON_CANCEL, 185, 255, 40, 20, 0, 0x0}, { BUTTON_CreateIndirect, "RIGHT", ID_BUTTON_RIGHT, 140, 270, 40, 20, 0, 0x0}, { BUTTON_CreateIndirect, "LEFT", ID_BUTTON_LEFT, 50, 270, 40, 20, 0, 0x0}, { TEXT_CreateIndirect, "Match", ID_TEXT_MATCH, 140, 15, 80, 20, 0, 0x0}, { TEXT_CreateIndirect, "ID", ID_TEXT_ID, 140, 40, 80, 20, 0, 0x0}, { TEXT_CreateIndirect, "", ID_TEXT_PROGBAR, 140, 65, 80, 20, 0, 0x0}, { LISTBOX_CreateIndirect, "Listbox", ID_LISTBOX, 5, 10, 120, 220, 0, 0x0}, { PROGBAR_CreateIndirect, "Progbar", ID_PROGBAR, 140, 85, 80, 20, 0, 0x0}, // USER START (Optionally insert additional widgets) // USER END};/********************************************************************** 上次工作时间**********************************************************************/static struct _Time Time_Last = { .s = 0, .ms = 0, .us = 0};/********************************************************************** 进度条開始的时间**********************************************************************/static struct _Time Time_Progbar = { .s = 0, .ms = 0, .us = 0};/********************************************************************** 接收CC1100的时间**********************************************************************/static struct _Time Time_Recv_CC1100 = { .s = 0, .ms = 0, .us = 0};/********************************************************************** 按键状态**********************************************************************/static struct _Key_State Key_State = { .ok = 0, .cancel = 0, .up = 0, .down = 0, .left = 0, .right = 0};/********************************************************************** 当前显示状态*0:未显示,1显示**********************************************************************/static uint8_t State_Show = 0;/********************************************************************** 进度条动画開始标志*0:终止,1:扫描,2:绑定**********************************************************************/static uint8_t Flag_Progbar = 0;/********************************************************************** 列表框存储器**********************************************************************/static struct _List List = { .len = 0};/********************************************************************** 已绑定脚镣ID*0:未绑定,其它:ID**********************************************************************/static uint16_t Fetter_Id_Bind = 0;/********************************************************************** 静态函数**********************************************************************//********************************************************************** 回调函数**********************************************************************/static void _cbDialog(WM_MESSAGE * pMsg);/********************************************************************** 定时工作**********************************************************************/static void slot_tick(void);/********************************************************************** 按键处理**********************************************************************/static void deal_key(void);/********************************************************************** 进度条动画*參数:percent:百分比**********************************************************************/static void progbar_show(uint8_t percent);/********************************************************************** 发送125k绑定信号**********************************************************************/static void emit_125k_bind(void);/********************************************************************** 处理cc1100接收数据*參数:task:0:扫描,1:绑定**********************************************************************/static void deal_cc1100(uint8_t task);/********************************************************************** 产生激发数据*參数:cmd:功能码* data:产生的2字节激发数据**********************************************************************/static void generate_exciter_data(uint8_t cmd,uint8_t *data);/********************************************************************** 函数**********************************************************************//********************************************************************** 模块加载**********************************************************************/void gui_match_load(void){ //新建界面 Handle_Gui = GUI_CreateDialogBox(_aDialogCreate, GUI_COUNTOF(_aDialogCreate), _cbDialog, WM_HBKWIN, 0, 0); gui_match_show(OFF);}/********************************************************************** 模块执行**********************************************************************/void gui_match_run(void){ struct _Time time; //推断当前是否显示 if (State_Show == 0) { return; } //推断当前是否处于扫描状态 if (Flag_Progbar == 1) { deal_cc1100(0); } else { //推断当前是否处于绑定状态 if (Flag_Progbar == 2) { deal_cc1100(1); } } //得到当前时间 get_time(&time); //推断是否到工作时间 if (sub_time(time,Time_Last) >= INTERVAL_GUI_MATCH * 1000) { //更新时间 Time_Last = time; //定时工作 slot_tick(); }}/********************************************************************** 设置显示状态*參数:enable:0:关闭显示,1:打开显示**********************************************************************/void gui_match_show(uint8_t enable){ WM_HWIN hItem; State_Show = enable; if (enable) { //设置列表框为焦点 hItem = WM_GetDialogItem(Handle_Gui, ID_LISTBOX); WM_SetFocus(hItem); WM_ShowWindow(Handle_Gui); } else { WM_HideWindow(Handle_Gui); }}/********************************************************************** 得到当前的显示状态*返回:0:关闭显示,1:打开显示**********************************************************************/uint8_t gui_match_get_show(void){ return State_Show;}/********************************************************************** 得到绑定的脚镣id*返回:0:未绑定,其它:脚镣id**********************************************************************/uint16_t gui_match_get_fetter_id_bind(void){ //return Fetter_Id_Bind; return 0x100;}/********************************************************************** 定时工作**********************************************************************/static void slot_tick(void){ uint32_t ms = 0; uint8_t percent = 0; WM_HWIN hItem; //按键处理 deal_key(); //推断当前进度条是否须要显示 if (Flag_Progbar) { //推断是否是扫描 if (Flag_Progbar == 1) { //推断激发信号是否结束 if (inf_exciter_get_busy() == 0) { //关闭激发模块电源 inf_exciter_power(OFF); } } //推断是否到工作时间 ms = sub_time(Time_Last,Time_Progbar) / 1000; if (ms < TIME_PROGBAR_GUI_MATCH) { percent = ms * 100 / TIME_PROGBAR_GUI_MATCH; progbar_show(percent); } else { //结束进度条动画 Flag_Progbar = 0; progbar_show(100); //文本:结束 hItem = WM_GetDialogItem(Handle_Gui, ID_TEXT_PROGBAR); TEXT_SetFont(hItem, &GUI_FontHZ12); TEXT_SetText(hItem,"结束"); } }}/********************************************************************** 按键处理**********************************************************************/static void deal_key(void){ WM_HWIN hItem; uint8_t index = 0; uint16_t id = 0; uint8_t data[3] = {0}; //推断下键是否按下 if (inf_key_detect_hold(KEY_DOWN)) { if (Key_State.down == 0) { Key_State.down = 1; //按键状态改变 hItem = WM_GetDialogItem(Handle_Gui, ID_BUTTON_DOWN); BUTTON_SetState(hItem,BUTTON_STATE_HASFOCUS | BUTTON_STATE_PRESSED); //发送按键信号 GUI_SendKeyMsg(GUI_KEY_DOWN, 1); } } else { if (Key_State.down == 1) { Key_State.down = 0; //按键状态改变 hItem = WM_GetDialogItem(Handle_Gui, ID_BUTTON_DOWN); BUTTON_SetState(hItem,BUTTON_STATE_HASFOCUS); } } //推断上键是否按下 if (inf_key_detect_hold(KEY_UP)) { if (Key_State.up == 0) { Key_State.up = 1; //按键状态改变 hItem = WM_GetDialogItem(Handle_Gui, ID_BUTTON_UP); BUTTON_SetState(hItem,BUTTON_STATE_HASFOCUS | BUTTON_STATE_PRESSED); //发送按键信号 GUI_SendKeyMsg(GUI_KEY_UP, 1); } } else { if (Key_State.up == 1) { Key_State.up = 0; //按键状态改变 hItem = WM_GetDialogItem(Handle_Gui, ID_BUTTON_UP); BUTTON_SetState(hItem,BUTTON_STATE_HASFOCUS); } } //推断扫描键是否按下 if (inf_key_detect_hold(KEY_OK) && (Flag_Progbar == 0)) { if (Key_State.ok == 0) { Key_State.ok = 1; //按键状态改变 hItem = WM_GetDialogItem(Handle_Gui, ID_BUTTON_OK); BUTTON_SetState(hItem,BUTTON_STATE_HASFOCUS | BUTTON_STATE_PRESSED); //文本:開始扫描 hItem = WM_GetDialogItem(Handle_Gui, ID_TEXT_PROGBAR); TEXT_SetFont(hItem, &GUI_FontHZ12); TEXT_SetText(hItem,"開始扫描"); //開始扫描 Flag_Progbar = 1; //保存当前时间 get_time(&Time_Progbar); //打开125k电源 inf_exciter_power(ON); //发送125k绑定信号 emit_125k_bind(); //清空列表框 List.len = 0; hItem = WM_GetDialogItem(Handle_Gui, ID_LISTBOX); listbox_clear(hItem); } } else { if (Key_State.ok == 1) { Key_State.ok = 0; //按键状态改变 hItem = WM_GetDialogItem(Handle_Gui, ID_BUTTON_OK); BUTTON_SetState(hItem,BUTTON_STATE_HASFOCUS); } } //推断清除键是否按下 if (inf_key_detect_hold(KEY_LEFT)) { if (Key_State.left == 0) { Key_State.left = 1; //按键状态改变 hItem = WM_GetDialogItem(Handle_Gui, ID_BUTTON_LEFT); BUTTON_SetState(hItem,BUTTON_STATE_HASFOCUS | BUTTON_STATE_PRESSED); //清空列表框 List.len = 0; hItem = WM_GetDialogItem(Handle_Gui, ID_LISTBOX); listbox_clear(hItem); } } else { if (Key_State.left == 1) { Key_State.left = 0; //按键状态改变 hItem = WM_GetDialogItem(Handle_Gui, ID_BUTTON_LEFT); BUTTON_SetState(hItem,BUTTON_STATE_HASFOCUS); } } //推断绑定键是否按下 if (inf_key_detect_hold(KEY_RIGHT) && (Flag_Progbar == 0)) { if (Key_State.right == 0) { Key_State.right = 1; //按键状态改变 hItem = WM_GetDialogItem(Handle_Gui, ID_BUTTON_RIGHT); BUTTON_SetState(hItem,BUTTON_STATE_HASFOCUS | BUTTON_STATE_PRESSED); //推断当前是否有项 if (List.len == 0) { return; } //得到脚镣id hItem = WM_GetDialogItem(Handle_Gui, ID_LISTBOX); index = LISTBOX_GetSel(hItem); if (index >= List.len) { //清空列表框 List.len = 0; hItem = WM_GetDialogItem(Handle_Gui, ID_LISTBOX); listbox_clear(hItem); return; } id = List.buf[index]; //数据 data[0] = 0; data[1] = 0; data[2] = 0; //等待能够发送 while (cc1100_judge_tx() == 0); //发送对码绑定帧 cc1100_tx(CMD_RF_BIND,id,data); //開始绑定 Flag_Progbar = 2; //保存当前时间 get_time(&Time_Progbar); //更新绑定的脚镣ID Fetter_Id_Bind = 0; //更新文本 hItem = WM_GetDialogItem(Handle_Gui, ID_TEXT_MATCH); TEXT_SetFont(hItem, &GUI_FontHZ12); TEXT_SetText(hItem,"未绑定脚镣"); hItem = WM_GetDialogItem(Handle_Gui, ID_TEXT_ID); TEXT_SetFont(hItem, &GUI_FontHZ12); TEXT_SetText(hItem,"ID:0"); //更新文本 hItem = WM_GetDialogItem(Handle_Gui, ID_TEXT_PROGBAR); TEXT_SetFont(hItem, &GUI_FontHZ12); TEXT_SetText(hItem,"正在绑定"); } } else { if (Key_State.right == 1) { Key_State.right = 0; //按键状态改变 hItem = WM_GetDialogItem(Handle_Gui, ID_BUTTON_RIGHT); BUTTON_SetState(hItem,BUTTON_STATE_HASFOCUS); } } //推断返回键是否按下 if (inf_key_detect_hold(KEY_CANCEL) && (Flag_Progbar == 0)) { if (Key_State.cancel== 0) { Key_State.cancel = 1; //按键状态改变 hItem = WM_GetDialogItem(Handle_Gui, ID_BUTTON_CANCEL); BUTTON_SetState(hItem,BUTTON_STATE_HASFOCUS | BUTTON_STATE_PRESSED); } } else { if (Key_State.cancel == 1) { Key_State.cancel = 0; //按键状态改变 hItem = WM_GetDialogItem(Handle_Gui, ID_BUTTON_CANCEL); BUTTON_SetState(hItem,BUTTON_STATE_HASFOCUS); //返回主界面 gui_match_show(OFF); gui_main_show(ON); } }}/********************************************************************** 进度条动画*參数:percent:百分比**********************************************************************/static void progbar_show(uint8_t percent){ WM_HWIN hItem; //进度条显示 hItem = WM_GetDialogItem(Handle_Gui, ID_PROGBAR); PROGBAR_SetValue(hItem,percent);}/********************************************************************** 发送125k绑定信号**********************************************************************/static void emit_125k_bind(void) { uint8_t data[2] = {0}; //生成激活数据 generate_exciter_data(CMD_125K_BIND,data); //生成新的激发序列 inf_exciter_generate_frame(data,2); //等待空暇 while (inf_exciter_get_busy()); //发送 inf_exciter_start();}/********************************************************************** 处理cc1100接收数据*參数:task:0:扫描,1:绑定**********************************************************************/static void deal_cc1100(uint8_t task){ struct _Rx_Buf_CC1100 buf; WM_HWIN hItem; char str[20] = {0}; buf = cc1100_get_rx_buf(); //推断是否是最新帧 if (compare_time(buf.time,Time_Recv_CC1100) != 2) { return; } //保存时间 Time_Recv_CC1100 = buf.time; if (task == 0) { //推断功能码是否是上传脚镣ID帧 if (buf.cmd != CMD_RF_UP_FETTER_ID) { return; } //推断是否还有存储空间 if (List.len >= LIST_LEN) { return; } //更新数据 List.buf[List.len++] = buf.src_id; sprintf(str,"%d",List.buf[List.len - 1]); //更新列表框 hItem = WM_GetDialogItem(Handle_Gui, ID_LISTBOX); LISTBOX_AddString(hItem, str); return; } if (task == 1) { //推断功能码是否是确认对码绑定 if (buf.cmd != CMD_RF_ACK_BIND) { return; } //更新绑定的脚镣ID Fetter_Id_Bind = buf.src_id; //更新文本 hItem = WM_GetDialogItem(Handle_Gui, ID_TEXT_MATCH); TEXT_SetFont(hItem, &GUI_FontHZ12); TEXT_SetText(hItem,"已绑定脚镣"); hItem = WM_GetDialogItem(Handle_Gui, ID_TEXT_ID); TEXT_SetFont(hItem, &GUI_FontHZ12); sprintf(str,"ID:0x%x",Fetter_Id_Bind); TEXT_SetText(hItem,str); return; }}/********************************************************************** 产生激发数据*參数:cmd:功能码* data:产生的2字节激发数据**********************************************************************/static void generate_exciter_data(uint8_t cmd,uint8_t *data){ uint8_t temp = 0; uint8_t check = 0; temp = cmd << 6; temp |= LOCAL_ID >> 4; data[0] = temp; temp = LOCAL_ID << 4; check = checksum4(data,2); temp |= check; data[1] = temp;}/********************************************************************** 回调函数**********************************************************************/static void _cbDialog(WM_MESSAGE * pMsg) { WM_HWIN hItem; switch (pMsg->MsgId) { case WM_INIT_DIALOG: { //初始化窗口 //添加小按键 FRAMEWIN_AddCloseButton(pMsg->hWin, FRAMEWIN_BUTTON_RIGHT, 0); FRAMEWIN_AddMaxButton(pMsg->hWin, FRAMEWIN_BUTTON_RIGHT, 1); FRAMEWIN_AddMinButton(pMsg->hWin, FRAMEWIN_BUTTON_RIGHT, 2); FRAMEWIN_SetFont(pMsg->hWin, &GUI_FontHZ12); FRAMEWIN_SetText(pMsg->hWin,"对码绑定"); //初始化列表框 hItem = WM_GetDialogItem(pMsg->hWin, ID_LISTBOX);// //设置内容// LISTBOX_SetFont(hItem, &GUI_FontHZ12);// LISTBOX_AddString(hItem, "0x10");// LISTBOX_AddString(hItem, "0x11");// LISTBOX_AddString(hItem, "0x12");// LISTBOX_AddString(hItem, "0x13");// LISTBOX_AddString(hItem, "0x14");// List.buf[0] = 0x10;// List.buf[1] = 0x11;// List.buf[2] = 0x12;// List.buf[3] = 0x13;// List.buf[4] = 0x14;// List.len = 5; //设置为焦点 WM_SetFocus(hItem); SCROLLBAR_CreateAttached(hItem, SCROLLBAR_CF_VERTICAL); //初始化按键 hItem = WM_GetDialogItem(pMsg->hWin, ID_BUTTON_OK); BUTTON_SetFont(hItem, &GUI_FontHZ12); BUTTON_SetText(hItem,"扫描"); hItem = WM_GetDialogItem(pMsg->hWin, ID_BUTTON_CANCEL); BUTTON_SetFont(hItem, &GUI_FontHZ12); BUTTON_SetText(hItem,"返回"); hItem = WM_GetDialogItem(pMsg->hWin, ID_BUTTON_UP); BUTTON_SetFont(hItem, &GUI_FontHZ12); BUTTON_SetText(hItem,"上"); hItem = WM_GetDialogItem(pMsg->hWin, ID_BUTTON_DOWN); BUTTON_SetFont(hItem, &GUI_FontHZ12); BUTTON_SetText(hItem,"下"); hItem = WM_GetDialogItem(pMsg->hWin, ID_BUTTON_LEFT); BUTTON_SetFont(hItem, &GUI_FontHZ12); BUTTON_SetText(hItem,"清除"); hItem = WM_GetDialogItem(pMsg->hWin, ID_BUTTON_RIGHT); BUTTON_SetFont(hItem, &GUI_FontHZ12); BUTTON_SetText(hItem,"绑定"); //初始化文本 hItem = WM_GetDialogItem(pMsg->hWin, ID_TEXT_MATCH); TEXT_SetFont(hItem, &GUI_FontHZ12); TEXT_SetText(hItem,"未绑定脚镣"); hItem = WM_GetDialogItem(pMsg->hWin, ID_TEXT_ID); TEXT_SetFont(hItem, &GUI_FontHZ12); TEXT_SetText(hItem,"ID:0"); hItem = WM_GetDialogItem(pMsg->hWin, ID_TEXT_PROGBAR); TEXT_SetFont(hItem, &GUI_FontHZ12); TEXT_SetText(hItem,"结束"); //初始化进度条 hItem = WM_GetDialogItem(pMsg->hWin, ID_PROGBAR); PROGBAR_SetBarColor(hItem,0,GUI_RED); PROGBAR_SetBarColor(hItem,1,GUI_GREEN); break; } default: { WM_DefaultProc(pMsg); break; } }}